自動閥的常見故障及解決方法?自動閥門是一種借助外力控制閥門的設備。具有操作方便、可靠、可遠距離和近距離控制等優點。自動閥在正常運行過程中有時會出現一些故障，為了更好地解決這個問題，我們應該了解一些常規的分析方法。
Common faults and solutions of automatic valve? Automatic valve is a kind of equipment that controls the valve with the help of external force. The utility model has the advantages of convenient and reliable operation, long-distance and short-distance control, etc. In order to better solve this problem, we should understand some conventional analysis methods.
1：閥門堵塞原因分析：
1: Cause analysis of valve blockage:
可能是通道太小，循環氣體中混入了一些雜物，導致通道堵塞。在這樣的環境中，活塞很可能會生銹和堵塞很長時間。此時，我們比較好的處理方法是拆開通道間管道，清洗干凈，干燥后安裝。
It may be that the channel is too small and some sundries are mixed in the circulating gas, resulting in channel blockage. In such an environment, the piston is likely to rust and block for a long time. At this time, our better treatment method is to disassemble the pipes between channels, clean them, and install them after drying.
2：當閥門無法調節或控制時：
2: When the valve cannot be adjusted or controlled:
主要原因可能是調節彈簧因其高強度而出現疲勞失效，或者是由于蓋接頭對接不良而導致無法控制的失效。
The main reason may be the fatigue failure of the adjusting spring due to its high strength, or the uncontrollable failure due to the poor butt joint of the cover joint.
3：自動閥的密封要求高。通常情況下，密封面泄漏是由于操作人員操作不當或設備在運行過程中出現問題造成的。
3: The sealing requirements of automatic valve are high. Usually, the leakage of sealing surface is caused by improper operation of operators or problems in the operation of equipment.
主要原因可能是密封面之間沒有緊密安裝，或密封件因腐蝕而不緊密。因此，操作人員應定期檢查，盡快查明泄漏情況，以免泄漏過于嚴重，甚至影響正常運行，損失更大。
The main reason may be that there is no tight installation between the sealing surfaces, or the seals are not tight due to corrosion. Therefore, operators should check regularly to find out the leakage as soon as possible, so as not to make the leakage too serious, even affect the normal operation and cause greater losses.
除了自動閥的故障分析和處理方法外，日常生活中的維護工作也是非常關鍵的，這樣才能預防故障，減少用戶的經濟損失。以上就是埃美柯閥門廠家的相關介紹，希望能夠?qū)δ兴鶐椭?/div>
In addition to the fault analysis and treatment methods of automatic valve, the maintenance work in daily life is also very key, so as to prevent faults and reduce the economic losses of users. The above is the relevant introduction of EMCO valve manufacturers. I hope it can be helpful to you.
This article is provided by Shanghai Lianggong valve. Our website is: http://m.258kmw.com We will provide you with services with wholehearted enthusiasm. Welcome to visit
企業公告：
